Announcement

Collapse
No announcement yet.

Probe ...where to stick it!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Probe ...where to stick it!

    Hi Yall,

    Now that the official CS DMM is available via bean bay, I plan to get my mitts on one soon.

    Just wondering about the thermocouple placement.
    From what Ive read, most users seem to recommend sticking it through the front of the BM, into the bowl at a height best suited to place it within the the bean mass.

    The only problem I see with this method is that I think its very likely Ill rip out the bowl at the end of the roast [before removing the probe] and destroy it.
    And that Ill probably make this mistake over and over again.


    Has any one mounted it from underneath?.....................Im thinking of putting a right angle bend in the TC/Probe so that it lies underneath the bowl and sticks up into it [about 1cm up into the beans].

    I guess the main concerns would be that this bend could damage/affect the TCProbe and also [but less likely] that the vertical intrusion may cause some problems with the movement of the beans.


    Your thoughts?

  • #2
    Re: Probe ...where to stick it!

    Good question Ruebster, I too will be getting a TC soon and have thought about what you have mentioned, I will be interesting to see what info your post receives....................

    Comment


    • #3
      Re: Probe ...where to stick it!

      reubster....

      Yes, through the side of the BM does work really well.... and yes, you sometimes forget to remove it before attempting to pull out the bowl :-[ :-[.... at least in the early days...

      But the probe is tough.... and survives this treatment well!!

      From the bottom.... if bent and accurately placed that should work.... it cant be fed up from underneath the base as the pulley is under the bowl... so would need to be located between the bowl and the inner skin... and locating it so that you dont hit the probe with the rotating paddle would be tricky.... as would feeding the probe into the bowl as it is inserted in the BM....

      I did think about doing that.... but then abandoned the idea.

      Comment


      • #4
        Re: Probe ...where to stick it!

        Originally posted by reubster link=1193370883/0#0 date=1193370883
        The only problem I see with this method is that I think its very likely Ill rip out the bowl at the end of the roast [before removing the probe] and destroy it.
        And that Ill probably make this mistake over and over again.
        Instead of a simple hole, why not create a vertical slot such that when the pan is removed, the probe just slides out and avoids being caught..... Should work ok providing the slot is kept to a close tolerance width of the probe. Probing the brain for lots of ideas ,

        Mal.

        Comment


        • #5
          Re: Probe ...where to stick it!

          Careful with that idea Mal. Chaff will find its way through that slot, and muck up whats underneath. A slot is what I use to remove chaff with my TO roaster.

          Comment


          • #6
            Re: Probe ...where to stick it!

            Originally posted by nunu link=1193370883/0#4 date=1193404826
            Careful with that idea Mal. Chaff will find its way through that slot, and muck up whats underneath. A slot is what I use to remove chaff with my TO roaster.
            Even when its well below the top of the bean mass nunu? I must admit I havent poked my nose into any other makes of BM, so only know the one we have and in our case there is nothing below the pan that would be "mucked up" at all.... Its all fully enclosed.

            Mal.

            Comment


            • #7
              Re: Probe ...where to stick it!

              Youd be surprised. A lot of the chaff gets sloughed off during agitation and will undoubtedly make its exit through the slot.

              My pot has a slot about 3cm up the side from the bottom. Its my main way of chaff removal, because the top is fully enclosed. The slot is about 3mm wide (about the size of the TC). It removes a good 85-90% of the chaff.

              Youd probably be better off having a hole in the corner of the pan diagonally.

              Comment


              • #8
                Re: Probe ...where to stick it!


                Not too sure how you would go putting a right angle bend in the probe... I briefly looked at doing that for the big roaster and the probe felt like it had epoxy (or similar brittle material) inside it. It might have just been the ceramic of the actual sensor that I could "feel".

                Anyway, I thought that it wasnt worth killing the probe so mine is still straight, maybe someone else will confirm it on theirs.

                Hang-on... ignore all the above.

                Hey reubster, its fine to bend the probe at right angles.



                Comment


                • #9
                  Re: Probe ...where to stick it!

                  Originally posted by Andy Freeman link=1193370883/0#7 date=1193728264

                  Hang-on... ignore all the above.

                  Hey reubster, its fine to bend the probe at right angles.


                  Yeah, let me know if it survives..... cause Ive thought of doing that as well ;D ;D ;D ;D ;D

                  Comment


                  • #10
                    Re: Probe ...where to stick it!

                    Thanks Andy + others,

                    Its good to know its "bendable"

                    Ive yet to buy the DMM+Probe [next BB], but I ll have a good sniff around the BM on the wend [when I roast up my first batch of Barahona AAA] to suss out the under-bowl mounting issues.

                    Comment


                    • #11
                      Re: Probe ...where to stick it!

                      Gday reubster (a.k.a. Bender ;D),

                      Just had a thought about this, you can get very small Tube Benders right down to about 3mm (smallest Ive seen) mostly used on copper, brass and steel tubing once used by Fuel Injection Techs and Instrument Makers. If you can find someone who still uses em you might be able to take the probe with you and have it bent properly with very little likelihood of damage to the innards. Might be worth chasing up ?

                      Mal.

                      P.S.
                      This is the sort of thing Im talking about, although you may be able to get miniature bending springs too but I havent come across them.

                      Comment


                      • #12
                        Re: Probe ...where to stick it!

                        Thanks Mal,

                        Thats a good idea, many thanks for the link.
                        I have a friend, an old school fitter & turner who makes brass light fittings and he may have something similar,.

                        Otherwise, Ill do an Andy and apply some GBF
                        [Gentle Brute Force]

                        Comment


                        • #13
                          Re: Probe ...where to stick it!

                          GDay

                          Does anyone have any pics of the probe inserted into the BM?  Since the paddle is where the beans are & the beans are where the probe needs to be, I thought the probe would be hit as the paddle rotated?  
                          Am I on the right track, or do I have it very wrong?  

                          Andrew

                          Comment


                          • #14
                            Re: Probe ...where to stick it!

                            gday back to you Secksy ...

                            I dont have personal pics, but suffice to that say my Ronson BM paddle agitates itself within a 10mm radius, within a 25mm sphere in the tin.

                            So, my DMM, being about 2inch long, having 15mm to work with, is inserted via drill-hole approx 5-10mm above base of tin to give me plenty of accurate tip sensor required readings, due to its immersion within the greenies.

                            The rotational diameter of the paddle in a BM leaves plenty of room within the tin for a (calculated) probe insertion ...

                            Comment


                            • #15
                              Re: Probe ...where to stick it!

                              Yes reubster, your assumptions are correct. Got my DMM/TC a couple of weeks ago and on first use pulled the pan up without removing the probe and put a bend in it. Got it right the second time but not the third. My probe goes through the front of the BM and protrudes about 10 mm into the pan and probably about 10 mm from the bottom. I used a 1/8" drill bit but that was just a tad too big. I use a bit of blu-tak to keep the probe still otherwise the vibrations from the BM work the probe into the pan and the paddle begins to hit it.

                              Chris

                              Comment

                              Working...
                              X