Announcement

Collapse
No announcement yet.

Quaha/Nemox/Lelit Steam Wand and Tip

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #61
    Re: Quaha/Nemox/Lelit Steam Wand and Tip

    Originally posted by 71535F5F5D5F5552533C0 link=1275289271/59#59 date=1304938954
    By the way - I saw on youtube one expert suggesting to heat the milk to 70 degrees, which I have since been doing. Ill reset the target to 60 as suggested by you and most others
    If using a thermometer theres some lag involved, so by the time it says 60 degrees and the thermometer pulled out,it would have reached the 65 degrees holy grail.

    Looking forwards to more feedback from yours and other Lelits as i have been eyeing off those babies for quite some time now.

    Bishop, do u mind putting up a video of your steaming technique on your Lelit?
    Ive seen a few on Youtube but not many available.

    Gary at G

    Comment


    • #62
      Re: Quaha/Nemox/Lelit Steam Wand and Tip

      Originally posted by 273D303123352D2727540 link=1275289271/60#60 date=1304948005
      Bishop, do u mind putting up a video of your steaming technique on your Lelit?Ive seen a few on Youtube but not many available.
      Been meaning to get around to it, but Im slack, will try and do it before the weekend...

      Comment


      • #63
        Re: Quaha/Nemox/Lelit Steam Wand and Tip

        Slack here too. Ive been meaning to do a how to video on the Sunbeam for others as well, if only i can get a tripod for the camera :.

        Gary at G

        Comment


        • #64
          Re: Quaha/Nemox/Lelit Steam Wand and Tip

          Ok, I was half through making a cup, and realized the camera was in the next room, so grabbed it for a quick video...
          http://www.youtube.com/watch?v=-Q6QHx5JPzM

          This was using my new 300ml jug, which I really like, when your working with the right jug they seem to have a sweet spot for volume, and right size means almost no wastage.

          Method was just a bit below the surface, crank on the steam sort of lower a bit while moving off center, vary to edge of jug trying not to break surface, move in depending on how much swirl you get so as not to overflow the jug, keep just below for about half the time and lower into the milk after though as it bulks this is not as necessary.

          And this was an average effort from me, I have done smoother, you can see its a little bit bubbly at the end, but it pours well and has a nice feel in the mouth, Im guessing many can do a lot better than me.

          Comment


          • #65
            Re: Quaha/Nemox/Lelit Steam Wand and Tip

            Talking about videos, I put on youtube a video of me pulling a double shot on the Lelit with the coffee beans roasted on another video (link on video).  http://www.youtube.com/watch?v=9WrDyB2yiBY

            I think Ill have to do a video on for frothing the milk to finish off the story (maybe when I get better at it).  The roasting video was on the second roast.  Since then Ive made a better agitator and I now use a 12 volt air-bed pump to cool down the beans.  A friend of mine saw the video and noticed I used compressed air and said that compressor oil may be contaminating the beans.  But I was already using the air-bed pump by then for convenience and for the much higher volume of air.

            About the steaming temp lag - I did notice the temp will continue to climb after turning off the steam and have been taking that into consideration. Some things I pick up naturally, other things I need to slapped several times in the head to get it!

            Comment


            • #66
              Re: Quaha/Nemox/Lelit Steam Wand and Tip

              The lag I dont think is huge issue, I think your average probe in general is more the issue, the three I have used all gave a different reading, so you have to be wary of that, and that they are slow to read changes in general.

              Right now Im backing the steam off when its just about to hit 60C and its coming in a bit above, though I dont think there is anything wrong with backing off when its nearing 65C if you want hotter milk, I know with the 60ish the coffee is drinkable right away, closer to 70C and its a lot hotter, good if your putting it in a take away cup for when your out the door somewhere.

              Comment


              • #67
                Re: Quaha/Nemox/Lelit Steam Wand and Tip

                In case you didnt see the link for the roasting then try this

                http://www.youtube.com/watch?feature=iv&v=PVfmghSFSaQ&annotation_id=annot ation_325575

                Comment


                • #68
                  Re: Quaha/Nemox/Lelit Steam Wand and Tip

                  Originally posted by 544556595C44435245370 link=1275289271/31#31 date=1282566440
                  Ill have to work out how to get the measurements without dismantling the machine. 0
                  Ill keep tinkering.
                  Crankster, did you have any luck with this type of mod? I have recently acquired a QUAHA with the same style wand and was pondering if I could retrofit my old IKON steam wand (also ball-joint)...

                  Comment


                  • #69
                    Re: Quaha/Nemox/Lelit Steam Wand and Tip

                    The new Lelit comes with a ball-joint steam wand. Is it possible to replace the old models stubby steam wand for this new one?

                    Comment


                    • #70
                      Re: Quaha/Nemox/Lelit Steam Wand and Tip

                      Hi everyone,

                      Just sharing my experiences and what I have done thus far with my Nemox Fenice steam wand. I had a custom adapter/tip made out of brass to help with length and to remove the enhancer



                      What I did experience yesterday was a leak coming from the ball joing of the steam wand.  I then noted that this is in fact removeable... this means you could easily buy another steam wand (Silvia/whatever) and give it a M6x0.75 male thread and install it.  I should have taken pics to illustrate this.

                      Here is a pic I found of the standard wand, see the threaded part on the top which screws into the ball joint:


                      Ill probably buy this  Breville 800es wand and try the above, its cheap and has a similar OD of the wand is a very close match to my fenice wand.
                      http://www.evilbay.com.au/itm/Breville-800ES-Coffee-Machine-Steam-Arm-Nozzle-/180694408970?pt=AU_CoffeeMakers&hash=item2a1239df0 a

                      Hope this provides some other people with some options around what thtey can do.

                      David

                      Comment


                      • #71
                        Re: Quaha/Nemox/Lelit Steam Wand and Tip

                        I just have a standard tip on Mokita combi and thought of swapping as I wasnt happy with my micro foam. Then I tried a new method of steaming. I put the steam button on and about 5 seconds after purge the wand of water and start steaming. I never run out of steam and can get a really good vortex going. Much better than waiting for the light to go out, then steaming.

                        Comment


                        • #72
                          Hello guys,


                          My Nemox Fenice is not as pleasing to steaming milk, I've tried everything, from what I saw this topic gregpullman the adaptations made ​​by placing the tip of the barrel of Silvia. This greatly improves? It's hard to get that pipe? I ask because I live in Brazil.


                          hugs.

                          Comment

                          Working...
                          X