Announcement

Collapse
No announcement yet.

Minore 2 - high bar pressure

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • maheel
    replied
    Re: Minore 2 - high bar pressure

    run a group head gauge over it.....

    Make your own for +-$25

    or

    Chris at TC once offered to let you do it for free # using his at his "shed", but you needed a spotless Ghead and ask nicely (buy some product?)
    #not sure if he still will?

    Leave a comment:


  • A_M
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 7B434A5F6944522B0 link=1285627937/12#12 date=1286237258
    5 minutes after being switched off...its now at .5
    funny...
    No...

    1: There is a bit of crap some where in teh bled lines

    OR

    2: It is the gauge




    Leave a comment:


  • PhatBoy
    replied
    Re: Minore 2 - high bar pressure

    5 minutes after being switched off...its now at .5
    funny...

    Leave a comment:


  • PhatBoy
    replied
    Re: Minore 2 - high bar pressure

    Not plumbed...lowest it will rest at is 1...
    Even when its turned off it still sits at 1

    Leave a comment:


  • A_M
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 676B626F6F660A0 link=1285627937/9#9 date=1286235190
    Originally posted by 0F373E2B1D30265F0 link=1285627937/8#8 date=1286233987
    Sits at 2bar when resting,
    is it plumbed?
    if not at rest should it not be on zero? (gauge fault?)
    Twas thinking the same...

    Have seen the odd one that will drop to Zero with a tap and or if the brew switch is run again with an open head..

    Not critical, but need to remember that any values will just be an indicator and without a real gauge... All subjective.

    Leave a comment:


  • maheel
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 0F373E2B1D30265F0 link=1285627937/8#8 date=1286233987
    Sits at 2bar when resting,
    is it plumbed?
    if not at rest should it not be on zero? (gauge fault?)

    Leave a comment:


  • PhatBoy
    replied
    Re: Minore 2 - high bar pressure

    Yeh...i know Chris...

    But thanks for the help guys...so easy to adjust.
    Sits at 2bar when resting, Hits 10bar when extracting and 9 bar when i end the shot.
    Sound ok??
    My tates buds seem a lot happier..a little more depth in the flavour

    Leave a comment:


  • TC
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 4A727B6E5875631A0 link=1285627937/6#6 date=1286105892
    thanks guys. will research it and give it a go. my friend just bought a new expobar lever and it hits the same bar
    Shame the mob that sold it didnt bother bench testing it :

    Leave a comment:


  • PhatBoy
    replied
    Re: Minore 2 - high bar pressure

    thanks guys. will research it and give it a go. my friend just bought a new expobar lever and it hits the same bar

    Leave a comment:


  • nick_stevens
    replied
    Re: Minore 2 - high bar pressure

    As far as i understood the OPV on a minore is on the front face plate behind the drip tray, but I could be mistaken. it is simple adjustment if you know what your doing, if not take it in for service and make sure you point out this as a problem or you might just get seals replaced but they are probably due anyway if its gone 2 years or more on the originals
    hope this helps

    Leave a comment:


  • Davie
    replied
    Re: Minore 2 - high bar pressure

    Have you tried reducing the pressure on the OPV? When you remove the drip tray you will see a hole in the frame. Behind the hole should be a visble screw, which is the OPV. I was told when I purchased my Minore 3 (which is set at factory at 12 bar) if you turn it counter clockwise by about 700 degrees (almost 2 complete turns) it would be reduced to about 9 bar.

    Leave a comment:


  • Koffee_Kosmo
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 172F263305283E470 link=1285627937/2#2 date=1285763514
    located in Melbourne.
    anyone had the same issue?
    I dont know if they are in an eastern suburb but give them a ring

    9Bar Espresso Services


    1 Grosvenor Street
    Abbotsford
    Vic 3067

    Leave a comment:


  • PhatBoy
    replied
    Re: Minore 2 - high bar pressure

    located in Melbourne.
    anyone had the same issue?

    Leave a comment:


  • A_M
    replied
    Re: Minore 2 - high bar pressure

    Originally posted by 645C5540765B4D340 link=1285627937/0#0 date=1285627937
    SE suburbs
    Why is it that every one assumes that  SE Suburbs is so easy to find in Darwin...

    An update as to your true location in ya profile might be a help..

    PS. If ya gauge is correct....  Then any number of predictabilities on offer.

    Leave a comment:


  • PhatBoy
    started a topic Minore 2 - high bar pressure

    Minore 2 - high bar pressure

    Has anyone had their expobar pushing 13 bar under extraction.
    Is it easy to fix? I havnt had it serviced, bought it 2nd hand 2yrs ago.
    If so, anyone around SE suburbs that can check it out?
    Thanks

Working...
X