Announcement

Collapse
No announcement yet.

Sunbeam EM0450 Coarse Grind

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Re: Sunbeam EM0450 Coarse Grind

    My mate is having a similar problem (fresh Campos beans, Gaggia Baby machine).
    I went over today and didnt understand it.
    On about 15, it grinds finely but sporadically - nothing comes out unless you bang it.
    Any finer setting - nothing comes out.
    We took it apart and cleaned it and reassembled it (several times), and now it grinds terribly coarsely on every setting with no change. I could only find one way that everything fit back together and we followed the manual.
    My brother in law has the same grinder with no problem, and Ive had an em0480 for 4 years with no hassles either.
    I have recommended he take it back to the shop (Harvey Norman) to exchange as it seems that the burrs are all out of whack. Its 3 months old and he has the receipt.
    Any other ideas before he does this?

    Comment


    • #17
      Re: Sunbeam EM0450 Coarse Grind

      Originally posted by 053E333F3D0F3324343923223F560 link=1300990310/15#15 date=1303804636
      On about 15, it grinds finely but sporadically - nothing comes out unless you bang it.
      Any finer setting - nothing comes out.
      It was set way too fine and this has compacted coffee grinds between the burrs and probably in the exit pathway as well.

      Originally posted by 053E333F3D0F3324343923223F560 link=1300990310/15#15 date=1303804636
      We took it apart and cleaned it and reassembled it (several times), and now it grinds terribly coarsely on every setting with no change
      You havent done it correctly, probably cross threaded. The burrs should have screwed together effortlessly - any resistance is either due to coffee in the thread, or cross-threading (not good).

      Originally posted by 053E333F3D0F3324343923223F560 link=1300990310/15#15 date=1303804636
      I went over today and didnt understand it.
      Correct.

      Originally posted by 053E333F3D0F3324343923223F560 link=1300990310/15#15 date=1303804636
      I have recommended he take it back to the shop (Harvey Norman) to exchange as it seems that the burrs are all out of whack.
      Might have been best to provide this advice at the outset. Fortunately, the staff at Harvey Norman are likely to know less about the grinder than yourselves, so you just might get away with it! ;D

      Comment


      • #18
        Re: Sunbeam EM0450 Coarse Grind

        Well its not much different to an EM0480 which I know well, there was no resistance, everything fit together smoothly and easily, but the grind was the issue. There was certainly no cross threading. Its as if the burrs are spaced either too far or too close with no in-between "sweet spot."

        Comment


        • #19
          Re: Sunbeam EM0450 Coarse Grind

          I didnt mean any offense, however as the grind was too fine at the outset, and following your intervention is now too coarse, unless Im missing something.... :-/

          Comment


          • #20
            Re: Sunbeam EM0450 Coarse Grind

            Assuming its a 0450 as per the thread title, its been put back together wrong.

            How far apart did you pull it for cleaning?
            Did you line up the arrows on the top burr holder with the body when you put it back together?

            Comment


            • #21
              Re: Sunbeam EM0450 Coarse Grind

              I was having problems with a coarse grind on a 480 sunbeam. I tried the fix using home made plastic shims. Works fine (pun intended) now. I noticed that when I had the machine apart that some broken beans were blocking the entry path and also that the area under bottom burr needed a clean. Have you checked that these pathways are clear?

              Comment


              • #22
                Re: Sunbeam EM0450 Coarse Grind

                Hi all, sorry to revive a dead thread, but i rang sunbeam to order a shim kit, and they knew nothing about them. any help???

                Comment


                • #23
                  Re: Sunbeam EM0450 Coarse Grind

                  I dont think they know them as a shim kit, I called a while ago and just told them about the issue and they sent me out washers immediately.

                  Good luck ,

                  Comment


                  • #24
                    Re: Sunbeam EM0450 Coarse Grind

                    Old post dig but I had this exact problem today and solved it. Noone has really explained the solution.

                    When you take these apart to clean them and then reassemble its easy to mess up steps 8 and 9 in the manual. When you put the adjustment collar back on it is important to line up the two markers, but then do nothing else. This is when you put the top burr in (also lining up those markers).

                    Then, and only then, you turn the adjustment collar clockwise.

                    Its very easy to mistakenly pop the adjustment collar on and instinctively turn it at this point (before you put the burr in), but if you do the top burr wont go in correctly. But (just to confuse you) the top burr will go in incorrectly (with the markers not lined up) and it will appear like its all good to go.

                    The easy way to test. If you can lift the top burr back out when you have the grinder adjusted right, you have installed it incorrectly. Go back and start again. Collar, burr, then turn collar.

                    Comment

                    Working...
                    X